Banner_Mortar
You are here:Home/Mortar/Specific Purpose/specific purpose

Cement mortar is used to produce CLC concrete blocks mixed with air bubbles and water at a given ratio.

>>Shop Now<<

USING

  • Mix mortar for lightweight block (M220B) with water using a mortar ratio of 1 bag (50 kg) per 7.0 liters of water.
  • Add bubbling agent at a given ratio. Mix the homogeneous mixture. Pour the prepared mixture. Should be used within 2 hours.

RAW MATERIAL

  • TPI Portland Type 1 Cement according to ASTM C-150 and TIS 15-2555.
  • Fine Crushed Limestone through the drying and sizing process.
  • Quality additives.

QUALITY OF USING

One ton of lightweight concrete blocks (M220B) can be produced as a 20 x 60 x 7.5 CM aerated concrete block with 120 slabs.

RFQ

Form by ChronoForms - ChronoEngine.com

Application for plastering on concrete walls / unmade concrete surfaces, monolithic brick walls and concrete blocks. Or in contact with chemicals such as fermentation ponds, treatment ponds, storage tanks or storage rooms, etc., have corrosion resistance properties with high acid. Concentration up to pH3 and can be mixed with rock for concrete.

>>Shop Now<<

HOW TO PREPARE THE USE OF PUTTY.

  • Clean the walls to be plastered, free from dust, oil, chemicals or anything that may affect adhesion. Then pour the water to damp. Then let dry.
  • Mix 1 M250 (20 kg) of M250 with 2.7 liters of water. Mix well. Leave for 5 minutes and mix again before use.
  • Bring the prepared plaster with polished steel trowel. By layer 5 mm each layer when the first dry. Then plaster the next layer to a thickness of about 10 mm when the plaster is dry, scrub it by the conventional polishing method.

HOW TO PREPARE CONCRETE

  • Mix 1 liter of M250 (20 kg) with 1/2 ""- 3/4"" stone and 3 liters of water to mix well. Leave it for about 5 minutes and mix again before use.
  • Bring ready-mixed mortar to the concrete. By general use.

SUGGESTION

  • When mixing or using, wear rubber gloves. Dust mask Or fabric off the nose. And be careful not to puncture the eyes. Or touch the body directly.
  • For acid-resistant plaster activated. Can be activated after 7 working days at normal conditions.
  • Can be activated after the work is completed one day when the temperature of 60 to 70 degrees for 24 hours.

TECHNICAL INFORMATION

Thickness of mortar (mm)/ Consumption of cement per 1 sq.m. (kg)/ Area with 1 bag of cement (sq.m.): 10/ 20/ 1

TECHNICAL INFORMATION FOR CONCRETE USE.

Thickness of mortar (m3)/ M250 mortar consumption (tons)/ Volume of 1/2 ""- 3/4"" (tons): 1/ 1.2/ 1

RFQ

Form by ChronoForms - ChronoEngine.com

Concrete Surface Repair Rapid Hardening in 4 hours

TPI M601 is a rapid hardening mortar with high adhesive strength bond. It is suitable for repairing the concrete surface to improve the strength and cracking area of concrete work. It is able to use in 4 hours after repaired. It can be used for both floor repairing works and new construction pattern more than 1 cm. Thickness. In case of the work which to be repaired is thicker than 4 cm.  TPI M601 can mix the  stone size ½” or ¾’ grade with ratio 30 kg of stone per 1 bag (50 kg of TPI M601)

>>Shop Now<<

Application

  • Mix 1 bag (50 kg) of TPI M601 with 5.5 – 6 liters of clean water until mixture is homogenous.
  • Apply on the cracked surface (cl
  • Apply on the cracked surface (clean the cracked surface before applying with mortar) by pouring at least 1 cm. and more thickness.
  • In case of more than 4 cm. thickness of concrete, it should be added stone size ½” or ¾’ in the mixture with the ratio 30 kg of stone per 1 bag (50 kg) of  TPI M601 mortar

Preparation

  • Clean the surface until the free from dust, oil, chemical and other contaminates to prevent  the  bonding  strength of the adhesion.
  • Remove all weak materials from the surface until the surface layer is strong enough.
  • Treat the surface with water and let to semi-dry surface before applying with mortar.

Precaution

  • Should not use with excess water to prevent for shrinkage and loss of compressive strength.
  • In case of adding stones. Should be used clean stones.
  • Enhancing the compressive strength when set the mortar by curing with water at least 3 days.

Usage Quantities and details

TPI M601 1 bag (50 kg)

TPI M601 50 bag (2,500 kg)

Water 5.5 – 6 liters

Water 275 300 liters

 Usage Quantities  : In case of mix with stone size ½’ or ¾’             

TPI M601 1 bag (50 kg)

TPI M601 50 bag (2,500 kg)

Stone  size ½’ or ¾’ 30 kg (3 buckets)

Stone size ½ ‘ or ¾ ‘ 900 kg (90 buckets)

Water 5.5 – 6 liters

Water 165 – 180 liters

             Suitable For Fast Setting Concrete Surface Repair, Cracks in Concrete Surface Repair

           

RFQ

Form by ChronoForms - ChronoEngine.com

Non - Shrink Grout

non – shrink grout hydraulic mortar with excellent flow property. It gives high compressive strength and no shrinkage. It is suitable for general construction and industrial construction works.

>>Shop Now<<

RFQ

Form by ChronoForms - ChronoEngine.com

Stucco

M900 is suitable for sculpture and art decoration in architecture.  After  mixing with water, it can be used easily and expediently and strong, durable performance. TPI M900 is proved by the professional sculptors with their recommended as follw.

TPI M900 has all the Good features to get perfect result according to their desires.

>>Shop Now<<

Application

  • For the base frame of sculpture, use with sand cement (mix TPI green Mixed Cement with sand)
  • Mix 3 parts TPI M900 with water 1 part by volume until the mixture is homogeneous.
  • Apply according to the general work procedure of stucco.

Remark

  • After mixed with water, it  should be used within 4 hours.
  • Keep in dry place away from moisture and humidity.
  • It should seal the bag tightly after opened.

Suitable for sculpture and Decorative the tracery with strong and durable.

RFQ

Form by ChronoForms - ChronoEngine.com

>>Shop Now<<

Cement base floor hardener powder (Non-iron) use a sprinkle on a new poured concrete surface. Then polished with polishing machine. Or scrub by hand according to the method of polishing it. To increase the hardness of the concrete surface. Suitable for areas where heavy traffic is used, such as department stores, warehouses, parking lots or concrete floors. Advantages of concrete using M99 is more resistant to abrasive than conventional concrete, smooth surface, easy to clean because of no metal powders. Protection of corrosion or rust. Available in several shades: light gray, red, green, yellow and blue.

SCOPE OF USE

Apply a sprinkle on a new poured concrete surface. Then scrub with a polishing machine or use the hand polishing method. Both indoor and outdoor flooring can be coated with Coating or can be used as a general abrasive concrete surface.

RAW MATERIAL

- TPI Portland Type 1 Cement according to ASTM C-150 and TIS 15-2555
- High abrasive resistance aggregate size and type of crystal structure. To obtain special hardness
- Quality additives Extra high adhesion strength. Increase hardness, etc.

HOW TO USE

  1. Pour the concrete level up to the standard level.
    Note: Suitable for concrete slump 10-15 cm. If slump concrete is less than this, it may be necessary to shake off the water in the M99 powdering process.)
  2. Sprinkle the TPI M99 to a full area, then trowel the surface with a triangular trowel to keep the M99 mortar dispersed evenly and smoothly.
  3. When the concrete is damp (Take 2-3 hours depending on weather conditions). When the plaster powder sucks the water from the concrete surface until it gets wet. Spin the top with a trowel or polished with a polishing machine. In order for M99 mortar to spread uniformly and smoothly.
  4. When setting M99 mortar, spin the face using a trowel or polishing machine. According to the method of polishing it.

Note

  1. After work, the surface should not be exposed to sunlight. Or hit the water because it will make the surface crack or smear.
  2. Store the product in the shade and dry the M99. When opening the bag, it should be used up. If left unused Put plastic bags and gag.

QUALITY OF USING

Thickness of mortar (mm)/ Area of ​​50 kg./ Usage per 1 sq.m.: 1-4 mm/ 8-10 sq.m./ 5-7 kg

RFQ

Form by ChronoForms - ChronoEngine.com

Super Asphalt is a thick, black and viscous liquid but it is flow-able and has good adhesion when filling along the joints of the concrete pavement or into the prepared slot /gap/crack area, and provides with flexible bonding performance. It is odorless and free of solvent or fuel oil. It is ready mixed Asphalt and can be used by open the container, stir the mixture homogeneously with no more heating to be melting and save the time.

>>Shop Now<<

RFQ

Form by ChronoForms - ChronoEngine.com